ECT 274 ECT274 ECT/274 ENTIRE COURSE HELP – DEVRY UNIVERSITY

Description

ECT 274 ECT274 ECT/274 ENTIRE COURSE HELP – DEVRY UNIVERSITY

ECT 274 Week 1 iLab B

ECT 274 Week 2 iLab

ECT 274 Week 3 iLab Binary Modulus Counters

ECT 274 Week 1 iLab

ECT 274 Week 1 Quiz

ECT 274 Week 3 Quiz

ECT 274 Week 4 Quiz

ECT 274 Week 5 Quiz

ECT 274 ECT274 ECT/274 ENTIRE COURSE HELP – DEVRY UNIVERSITY

ECT 274 Week 3 iLab Binary Modulus Counters

I.OBJECTIVES

In this lab, you will create a binary MOD-10 up-counter ARM project.

II.DESCRIPTION

A MOD-10 counter has 10 states. For this lab, the count sequence will start at state zero and count to state nine. The count sequence will be displayed on the LEDs and on the OLED display. The VI utilizes the ReadWriteIOBoard SubVI located in the C:\DEVRY\IOBOARD folder to output the binary number to the LEDs.

ECT 274 ECT274 ECT/274 ENTIRE COURSE HELP – DEVRY UNIVERSITY

ECT 274 Week 1 iLab

Title: Creating SubVIs

I.OBJECTIVES

In this lab, you will build SubVIs by using a selection of components from an existing VI. The VI will calculate the total resistance, current, and power of a two-resistor series circuit.

ECT 274 ECT274 ECT/274 ENTIRE COURSE HELP – DEVRY UNIVERSITY

ECT 274 Week 1 Quiz

1. (TCO 1) The VI block diagram shown below manipulates numeric values. You are asked to add an indicator to display output value with two digits of precision. Which data type should you use for the indicator?

2. (TCO 1) The VI block diagram shown below manipulates numeric values. Given that input X is 5, which will be displayed on the indicator?

3. (TCO 1) The VI block diagram shown below manipulates numeric values. Given that input X is 6 and Y is 7, what will be displayed on the indicator?

4. (TCO 1) The VI block diagram shown below manipulates numeric values. Given that input X is 5.5 and Y is 8.5, which will be displayed on the indicator?

5. (TCO 1) Given the code snippet below, which does the red dot indicate?

6. (TCO 1) Given the VI diagram below with input X = 5, which will be displayed on display Y after the VI is run?

7. (TCO 1) Given the VI diagram below with input X = 5, which will be displayed on display Y after the VI is run?

8. (TCO 1) Given the VI diagram below with input X = 5, which will be displayed on display Y after the VI is run?

9. (TCO 1) Given the VI diagram below with input X = 5, which will be displayed on display Y after the VI is ran?

10. (TCO 1) Given the VI diagram below with input X = 5, which will be displayed on display Y after the VI is run?

ECT 274 ECT274 ECT/274 ENTIRE COURSE HELP – DEVRY UNIVERSITY

ECT 274 Week 3 Quiz

1. (TCO 3) In the VI block diagram shown below, control X = 8, control Z = 0, and control Y = 1,000. Which will be displayed on the indicator T?

2. (TCO 3) In the VI block diagram shown below, control X = 6, control Z = 2, and control Y = 1,000. Which will be displayed on the indicator T?

3. (TCO 3) In the VI block diagram shown below, control X = 6, control Z = 3, and control Y = 1,000. Which will be displayed on the indicator T?

4. (TCO 3) In the VI block diagram shown below, control X = 7, control Z = 1, and control Y = 10. Which will be displayed on the indicator T?

5. (TCO 3) In the VI block diagram shown below, control X = 7, control Z = 1, and control Y = 100. Which will be displayed on the indicator V?

6. (TCO 3) In the VI block diagram shown below, control X = 7, control Z = 1, and control Y = 100. Which will be displayed on the indicator V?

7. (TCO 3) In the VI block diagram shown below, control X = 7, control Z = 1, and control Y = 10. Which will be displayed on the indicator V?

8. (TCO 1) The VI block diagram shown below manipulates numeric values. Given that input X is 5.00 and Y is 7.00, which will be displayed on the indicator T?

9. (TCO 1) Given the VI diagram below with input X = 6, which will be displayed on display Y after the VI is run?

10. (TCO 2) Given the VI diagram of an ARM I/O board driver, which need to be entered at “Board Component”, “Operation”, and “Data To Board” in order to turn off all LEDs?